making reagular2cooking regular2lovingliving regular2new reader3

Monday, January 20, 2014

The Leather Tag

Thank you for all the positive comments and feedback on the leather tag! Several of you have asked me how I made it and with what tools. Here is a tutorial for you in case you would like to make your own initials tag hat.




You need:
1. cutting mat
2. polymer or wooden mallet (do not use a metal hammer or metal tool as this will damage your leather stamps)
3. leather
4. alphabet stamps for leather
5. hole punch (2mm)
6. stamp handle
7. rotary cutter (or tapestry knife)
8. ruler
9. sponge
10. polymer cutting board or a wooden cutting board (not shown in the photos)

Cutting the leather
Cut your piece of leather into strips and cut each strip into several tags. My initials hat tag is 85mm long and 12mm wide. I also make other sizes depending on what kind of garment I am using them on. When making tags for hats I let the brim of the hat decide how wide and long the tag should be. For slippers I make a wider tag, and so on. I use the same rotary cutter I use for fabrics, a metal ruler and a cutting mat to protect my kitchen countertop.

Surface casing
You need to moisten the leather before stamping, this is called casing. There are two basic methods of casing, surface-casing and thru-casing. Which method is best depends on the thickness and size of your leather to be stamped. If it is a heavy weight leather and a big piece, you should use the thru-casing method. If the leather is lightweight and small you can use the surface-casing method.

My leather tags are small pieces of lightweight leather so I have used the surface-casing method. Surface-casing is when you wet the leather with a sponge on the skin-side of the surface. I however, did it on both the skinned side and on the flesh side (yes, I experimented a bit). Fill a glass bowl or a plastic container with water (metal containers can cause the leather to stain). With clean hands, apply the water as evenly as you can and dry of excess water that forms on top of the leather, (I have not done that yet in the photo above).

The rule of thumb is that if the leather is to dry when stamping, you will have to use excessive force and the leather will not accept the stamp impressions (This is exactly what I experienced with my first initials hat). If the leather is too wet it will form deep initial impressions, but will not retain the impression after it has dried. Try to moisten only the leather you are going to use there and then. If not you might have to re-moisten the leather too many times (which is not good).

When the leather begins to return to its natural colour, but still feels moist to the touch; begin stamping.



Stamping the letters
Place a polymer or wooden cutting board on a firm surface like a table or kitchen countertop. Place the leather on your cutting board, which will be your work surface. Place the letter stamps on your leather. Place the stamp handle in one of the letter stamps.



Make sure you hold the handle down firmly while striking with the mallet. If you are stamping more than one letter, place the stamp handle on the other letter, place it on the leather and repeat the procedure.



Use the hole-punch to make holes in the tag. Place the hole-punch where you would like the holes and strike with the mallet (but not as hard as when you were letter stamping). Your are now ready to sew your tag onto your knitted garment.


There are several alphabet stamp fonts. I bought the bottom one in Barcelona this fall, but I think my favourite is the one in the top. There are many different fonts and sizes in leather shops, hopefully you can find one that is right for your project.

If you decide to make an initials tag after reading this tutorial, and you blog about it, I would be happy if you link back to this post, as thanks. Oh, and please let us know what you plan to use the tag on, to continue the upward-inspiration-spiral. Thank you!

To read more about casting leather, visit this article by B. J. (Kirk) Kuykendall

12 comments:

  1. Thank you AM! I would love to make tags if I could find the equipment. Maybe when I am in Madrid in March....it's not so common in the UK.

    ReplyDelete

  2. Det finnes så utrolig mye nytt å lære og dette var interessant.
    Kanskje jeg prøver en gang, jeg har det meste uten selve stemplene - får se om det går å få kjøpt i en eller annen hobbybutikk.
    Men hvordan oppfører læret seg etter vask? Jeg antar at luene du har brukt disse merkelappene på må vaskes av og til - tar du merkelappene av før vask og syr dem på igjen etterpå?

    ReplyDelete
    Replies
    1. Godt spørsmål. Jeg har enda ikke vasket luene etter at jeg sydde på skinnlappen. Vil tro at det skal gå greit å vaske de for hånd med tanke på at skinnlappen ble behandlet med vann før stempling av bokstavene. Men vet det ikke. Vi vasket nettopp en lammeskinnsfell (slik man bruker til babyer) i vaskemaskinene etter en runde med omgangssyke. Det ser ut til å ha gått greit, så jeg satser på at det også går greit med luen. Skal si ifra hvis hvordan det gikk etter vask :-)

      Delete
  3. Så utrolig bra! Jeg har hatt så lyst å prøve dette etter at jeg så lua di ♥
    Utstyret er imidlertid ganske dyrt, men fristelsen er stor!!

    ReplyDelete
  4. Kjempebra tutorial, gode forklaringer og bra bilder! Så flink og kreativ du er:)

    ReplyDelete
  5. Wow -- Thanks for the tutorial! I have little alphabet stamps that I use for metal stamping -- I wonder if they would also work for leather. Very cool!

    ReplyDelete
  6. La verdad es que esas etiquetas de cuero le dan a cualquier prenda un toque fantástico, gracias por el tutorial, no parece dificil de hacer si tienes el material!!!!

    ReplyDelete
  7. Wow! Takk for at du tok deg tid til tutorial! Veldig utførlig og fin!

    ReplyDelete
  8. It is really a nice detail ... very cool :)

    ReplyDelete
  9. Ooooh!! Ahora necesito como loca un alfabeto como ese y todo el resto de instrumentos, jijiji
    Muchas gracias por el tuto!!

    ReplyDelete
  10. These are really lovely, and I just love that sweater in the post above too xx

    ReplyDelete

Thank you for letting me know you were here!